A STEP-BY-STEP GUIDE TO SETTING UP A BATHTUB

A Step-by-Step Guide to Setting Up a Bathtub

A Step-by-Step Guide to Setting Up a Bathtub

Blog Article

Quote

Do you find yourself searching for advise about Installing A Bathtub?


Installing A Bathtub
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently available, the task can move speedily; if you need to open a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is much harder. In either situation, the project is within a residence handyman's skills, although you will certainly require a helper to vacate the old tub and embeded in the new one. Make certain you have certified yourself for the task and also are comfortable trying it. Instead of employing a service provider to take control of a halfway-completed project, it is much better to consider using one before you start. Possibilities are you may require a professional plumber to make tube connections.
This article will certainly help you set up a new tub in your bathroom if you have actually already gotten a new tub and don't require to alter the setup of your previous supply of water pipelines.
Your devices as well as product list ought to make up the following:
  • New Bath tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the restricted gain access to that is often the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have actually been removed, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any kind of old securing substance.
    Before proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end gives a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
    Next, position the tap in the mounting hole in the bath/basin ensuring that the washing machines remain in area in between the tap and the sink. Secure the tap in position with the supplier given backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, position the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 little points.
    The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub up until the spirit level reviews degree.
    To install faucets, fit all-time low of the furthest adaptable tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
    Switch on the water supply and also inspect all joints and brand-new pipework for leakages and tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
    Lastly, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the bath tub has been made use of at least when as this will resolve it right into its final placement.

    Getting ready for the Installment


    Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to prevent pressure on the bathtub.
    Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you use every one of the provided washers.
    Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to now prepare to be fitted in its last placement.

    Tiling Around the Bath tub


    In the area where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, creating the water to pass through the wall surface in between the bathroom and also the tiling, leading to complications with dampness and possible leaks to the ceiling below.
    You can choose from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub remains in usage. The sealer can split relatively early if you do not consider this motion before securing.
    Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly available on the market. It is recommended to fit the tiles using water-resistant or water-proof sticky as well as grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    Do you appreciate reading about Tools You Need to Install a New Bathtub ? Put a review down below. We would be pleased to see your views about this blog posting. We hope that you come back again in the near future. Those who liked our article if you please remember to pass it around. Thanks so much for going through it.




    Information


    Report this page